処女の最初のセックス

Q1：　Difference between "external contact type" of "internal contact type"?
Q2：　What is the "repeatability"?
Q3：　Is it can be mounted other than the standard stylus? Please tell us also about the length or
　　　　size.
Q4：　What is the Waterproof IP67 (IEC standard)?
Q5：　Please tell me the difference between general stylus (steel stylus, etc.) and "non-magnetic
　　　　stylus".
Q6：　Differences in non-ferrous metal and non-metal? Also, I use external contact type (energized
　　　　type)?
Q7：　What is the "centering"?
Q8：　It has been described as W6 and W4 centering gauge, but what do you thing?
Q9：　What does it mean the machine tools is the magnetization?
Q10：　Where centering gauge swing type and point finder Do you difference?
Q11：　Can I redeem yourself with the stylus?
Q12：　I'd like to adjust the stylus.
Q13：　Why repeat accuracy is do you a world?
Q14：　Why do I need to repeat accuracy?
Q15：　I want to measure the length of the drill of φ0.05 tool setter, but either of i-50 and
　　　　　M-50 is good?
Q16：　The cutting edge measurement of the end mill of φ6mm, both of i-50 and M-50 or is a good
　　　　　tool setter?
Q17：　Where What is the difference between i-50 and M-50 of the tool setter?
Q18：　What is difference of M-50 and S-50 of the tool setter?
Q19：　You are using both of the conduction equation with the dial-a tool setter, but why dimensions
　　　　　of different areas?
Q20：　Can I use the viewfinder point the machine tools of horizontal?
Q21：　Is there more than 10 degrees the temperature of the day and evening and the morning, but
　　　　　do not affect the processing and measurement?
Q22：　Machine or does not wear electric field energized expression because flow electricity to the
　　　　　machine?
Q23：　I measure the casting. It is a brass such as aluminum or iron or. There is that I am using
　　　　　energized electric flows, but not stick sometimes. Why?
Q24：　Can I use a leave was put into the ATC waterproof?
Q25：　The battery does not have a year.
Q26：　Can I use a horizontal the machine tools Rotary Center?
Q27：　I'd like to buy a lithium battery at overseas.
Q28：　We want to control the machine of your own, but do you take the signal from the point
　　　　　finder?
Q29：　The stylus of the case, "Using other than our products will be patent infringement"
　　　　　There is a poster with. I will question.
Q30：　Is it possible to measure the exact angle of the gradient loose and tight gradient.
Q31：　Align the vernier to use to sign vice in mold parts processing and has been accurately
　　　　　measured.
Q32：　Or the tip of the stylus would not it be best cylindrical shape than a sphere?
Q33：　From three-point coordinates of the outline rounded surface of the template of radius
　　　　　r and center x, I want to measure the y coordinate.
Q34：　I will tracking the three-dimensional processing curved surface at the point file fin
　　　　　ers. Figure I want to express in a three-dimensional manner.

	I'd like to adjust the stylus.
	Method to make heart touch adjustment of stylus is not right. It is known that there is sensor which we can adjust set screw (screw) smaller than the outside to from right and left. As for the mechanism to let you screw from right and left, power to unscrew each other so as to close if we strongly close works, and set screw melts by shock that there is a few. We do not know when you melted which right and left screw loosened. If there is not function telling that we melted, it leads to measurement error. We melt to screw which must not loosen by all means, and common sense of design to have to give end is not protected. POINT FINDER three points each do slack end by double nut method by fixed method. We fix all three places of them with same clamping power using torque wrench. When balance of three places of clamping power collapses, it becomes easy to melt.
	Clean degree makes up from note) inside point of contact method in room of level 3 and adjusts. Dust is pervasive at level 6 in general environment. Dust enters inside when we exclude Bellows in the environment, and LED comes to keep on there being. Please absolutely stop the resolution.
	[about heart touch] We can greatly measure at 1μm so that heart touch of POINT FINDER is visible. It is easy than we do dangerous adjustment. You see the right figure and explain principle. It becomes easy to be really revealed that we perform while writing the X-axis and the Y-axis on paper like the right figure when it is confirmed quantity of heart touch. Position of stylus assumes POINT FINDER with A point in main shaft fixed position [position of orientation]. 1.We measure touch of the X-axis. We measure fixed gage block on the table. We reset X-axis value of CRT at position that LED turned on. We separate once next and turn off LED. We turn main shaft 180 degrees (± 2-3 degrees that we do not almost mind does not emerge to error) and will have B point and measure again. Place of 1/2(37.641) of value (75.282) that was displayed by CRT when LED turns on is the center of the X-axis. The value (37.641) is touch of the X-axis. 2.We measure touch of the Y-axis. Because it is hard to attach gage block to Y-axis direction, we turn main shaft 90 degrees (± 2-3 degrees does not emerge to error) [please fill out paper not to get a wrong + turn or - turn]. We turn to C point during figure. Touch of the Y-axis is demanded if we measure in this in direction same as the measurement of the X-axis. Place of 1/2(23.102) of moving distance (46.204) of the Y-axis is the center of the Y-axis. The value (23.102) is touch of the Y-axis. You add value of the X-axis Y-axis and radius (in the case of illustration 3mm) of stylus, and please input for offset of machining center. [prevent coordinate being -, or + from being wrong] + Touch of coordinate of edge face is revised if we push button in place where LED turned on at the time of getting out heart if it is machine tools which there is of input function.
	Products that are relevant to this question is as follows. It will jump to the corresponding page by clicking. [Point Finder Series]　　[Centering Gauge Swing Type]